Im LCOS 6.30 funkzionirt das dynamisches VLAN nich mehr

[rokpapez]

Moin!

Ich habe das neu 6.30.0022 firmware ausprobiert und habe probleme
mit dynamischem VLAN. Die VLAN3 und VLAN4 funkzioniren einvandfrei
wenn ich die VLAN im AP anstelle:

cd /Setup/VLAN/Port-Table
tab Port Use-Tagging Allow-Untagged-Frames Allow-All-VLANs Port-VLAN-Id
set "LAN-1" Yes No Yes 0
set "WLAN-1" No Yes Yes 4

und mit:
cd /Setup/VLAN/Port-Table
tab Port Use-Tagging Allow-Untagged-Frames Allow-All-VLANs Port-VLAN-Id
set "LAN-1" Yes No Yes 0
set "WLAN-1" No Yes Yes 3

Das funkzionirt einwandfrei. DHCP, ping, web.. alles laüft.

> sysinfo

DEVICE: LANCOM L-54g Wireless
HW-RELEASE: D
SERIAL-NUMBER: 053890600416
MAC-ADDRESS: 00a05711d602
IP-ADDRESS: 0.0.0.0
IP-NETMASK: 255.255.255.0
INTRANET-ADDRESS: 10.10.121.77
INTRANETMASK: 255.255.255.240
VERSION: 6.30.0022 / 09.02.2007
NAME: lancom2
CONFIG-STATUS: 1056;0
FIRMWARE-STATUS: 0;0;1;6.30.09022007.10;6.12.29052006.11
HW-MASK: 00001100000000000000000000000010
FEATUREWORD: 00000000000000000100000000010000
REGISTERED-WORD: 00000000000000000100000000010000
TIME: 00000000000000
HTTPS-PORT: 443

Aber wenn ich mit FreeRADIUS versuche die VLAN dynamisch anzushtellen:
Sending Access-Accept of id 133 to 10.0.121.77 port 3072
User-Name = "test@lab"
Tunnel-Type:0 = VLAN
Tunnel-Medium-Type:0 = IEEE-802
Tunnel-Private-Group-Id:0 = "3"
MS-MPPE-Recv-Key = xxx
MS-MPPE-Send-Key = xxx
EAP-Message = 0x03050004
Message-Authenticator = 0x00000000000000000000000000000000

Dann hangt alles :-/ (Auch wenn die VLANs die selben sind). Kein DHCP, ping,
traceroute, web, ... Das Accounting Start record wird auch nicht gesendet. Im
/Status/WLAN/Station-Table sehe ich das die VLAN-Id am 3 engestellt ist:

> dir /Status/WLAN/Station-Table

Index AID Interface Network VLAN-Id Age Phy-Signal MAC-Address User-Name Identification Tx-Bytes Rx-Bytes Throughput Max.-Throughput Tx-Packets Rx-Packets Tx-Limit Rx-Limit State MAC-Check Last-Event Tx-Rate Rx-Rate Antenna WPA-Version QoS Key-Type Power-Saving Listen-Interval Connect-Time Short-Preamble Short-Slot-Time Compression Cl.-Brg.-Support IP-Address
----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
1 1 WLAN-1 1 3 59 3 000cf138a2ba test@lab 0 0 0 B 0 B 0 0 0 0 1x-Negotiation none Assoc-Success Unknown Unknown 0 WPA2 No AES-CCM active 10 0 No No None No 0.0.0.0

========================================
Mit dem firmware 6.12.0005 funkzionirt das alles einwandfrei.

root@lancom2:/
>dir /Firmware/Table-Firmsafe

Position Status Version Date Size Index
-------------------------------------------------------------
1 inactive 6.30 09022007 1658 10
2 active 6.12 29052006 1541 11
3 <loader> 1.86 15062005 0 0

root@lancom2:/
> sysinfo

DEVICE: LANCOM L-54g Wireless
HW-RELEASE: D
SERIAL-NUMBER: 053890600416
MAC-ADDRESS: 00a05711d602
IP-ADDRESS: 0.0.0.0
IP-NETMASK: 255.255.255.0
INTRANET-ADDRESS: 10.0.121.77
INTRANETMASK: 255.255.255.240
VERSION: 6.12.0005 / 29.05.2006
NAME: lancom2
CONFIG-STATUS: 1056;0
FIRMWARE-STATUS: 1;1;1;6.30.09022007.10;6.12.29052006.11
HW-MASK: 00001100000000000000000000000010
FEATUREWORD: 00000000000000000100000000010000
REGISTERED-WORD: 00000000000000000100000000010000
TIME: 09550828032007
HTTPS-PORT: 443

[rokpapez]

Mit dem neuen firmware läuft das OK. Danke alf29 .

[langewiesche]

was war es denn?

EDIT: OK schon verstanden